Choosing Shrink Film for Automatic Wrapping Machines
A loose, wrinkled package coming off a production line usually gets blamed on the machine. More often, the film is wrong for the product, and the settings were never adjusted to match it. Film choice decides how a package looks and how reliably it seals long before anyone touches the temperature dial. This comparison walks through the main film families and shows which settings each one needs on a shrink tunnel Machine and the wrapping unit feeding it.
The main shrink film types and what each one does well
Shrink film is sold by material family, thickness and roll width. Each family responds differently to heat, which is why one film can look glass-clear on a carton and cloudy or torn on a soft item. Match the film to the product first, then tune the tunnel.
Polyolefin (POF) film
POF is the general-purpose choice for retail multipacks, boxed goods and printed cartons. It shrinks evenly in both directions, stays clear and does not give off chlorine-based fumes. It suits a Shrink wrapping machine running moderate speeds where appearance matters. Thin gauges need gentler heat or the film will burn through at the seal.
Polyethylene (PE) film
PE is tougher and cheaper per kilo, so it dominates industrial bundles, beverage trays and hardware packs. It shrinks mostly in one direction, so packages can look slightly loose at the ends unless the film is oriented correctly on the roll. PE needs higher tunnel temperatures and longer dwell than POF, and it tolerates heavier products without puncturing.
PVC film
PVC gives a tight, glossy finish and shrinks at lower temperatures, which makes it popular for small consumer items and stationery. Its downside is that it releases corrosive fumes when overheated, so tunnel ventilation and exhaust matter. Many facilities are moving away from PVC for environmental and worker-safety reasons.
Crosslinked and multilayer films
Crosslinked PE is stronger and more resistant to tearing, which helps when wrapping sharp-edged or heavy items. Multilayer films combine a stiff outer layer with a soft sealing layer, giving a cleaner seal on high-speed lines. These cost more, so they make sense only where reject rates or product damage justify the premium.
| Film | Best for | Tunnel temperature | Watch out for |
|---|---|---|---|
| POF | Retail multipacks, printed cartons | Moderate | Burn-through on thin gauges |
| PE | Industrial bundles, trays, heavy goods | Higher | Loose ends from one-way shrink |
| PVC | Small glossy consumer items | Lower | Fumes, overheating |
| Crosslinked PE | Sharp or heavy products | Higher | Higher film cost |
Matching film to machine settings and product shape
Once the film family is fixed, the settings on an Automatic Shrink Wrapping machine and its tunnel need to follow the film, not the other way around. Three variables do most of the work: tunnel temperature, conveyor speed and the sealing bar’s heat and time.
Temperature and speed
Thicker PE film needs a hotter tunnel and slower conveyor so heat reaches the core of the film before the package exits. Thin POF needs the opposite: lower heat and faster movement to avoid melting the seal. If a package exits with wrinkles near the edges, the film is usually cooling before it finishes shrinking, so slow the conveyor slightly or raise the tunnel temperature in small steps.
Sealing bar settings
The sealing bar must cut and close the film without weakening it. Too much heat creates a brittle seal that splits in the tunnel; too little leaves a weak join that opens in transit. Adjust seal time in small increments and test with a pull test on a finished pack rather than judging by eye.
Product shape and film orientation
Flat cartons wrap cleanly with almost any film. Cylindrical or irregular items need film oriented so the strongest shrink direction runs around the curve, otherwise the package tightens at the middle and stays loose at the ends. Sharp corners call for thicker or crosslinked film, and soft products need lower heat so the film does not crush them.
- Set tunnel temperature first, then conveyor speed.
- Tune the sealing bar last, using a pull test.
- Re-check settings whenever the film roll is changed.
- Keep a sample pack from each film batch for comparison.
Common film mistakes that cause poor shrink results
Most bad packages trace back to a handful of avoidable errors. Fixing them costs nothing and saves film.
Using a film too thin for the product is the most common. The film stretches during wrapping, then tears at the seal or leaves a baggy finish. Moving up one gauge often solves it without touching the machine.
Storing film in a cold or humid area changes how it behaves in the tunnel. Film should be kept at room temperature and away from direct sunlight so it shrinks predictably from the first pack of the shift.
Ignoring roll width and orientation wastes film and causes loose ends. The roll should match the package width closely, and the film’s shrink direction should be checked against the product shape before the line starts.
Finally, never change film and machine settings at the same time. Change one variable, run a few packs, and inspect the result. That discipline keeps the line predictable and makes it obvious whether the film or the settings caused a problem.